ABB Module SAFT190APC SAFT190 APC POWER SUPPLY Online hot welcome to buy

Product Specification

ABB Module SAFT190APC SAFT190 APC POWER SUPPLY Online hot welcome to buy

Product Description:

nput voltages that exceed the measuring range cause the overflow numerical value of +32767. If the measured value is below the range, the underflow numerical value Input currents that exceed the measuring range cause the overflow numerical value of +32767. If the measuredvalue is below the range, the underflow numerical value of -32767 is set. The input impedance is ca. 330 Ω. The current input has a self-protecting mechanism. If the input current gets too high, the shunt is switched off and the value for range overflow is generated. About every second, the unit tries to switch on the shunt again. In this way the correct measurement will succeed after the current has reached a normal value again.1 or 2 (see also the chapter "High-speed counter").Features of the analog inputs:The 8 analog inputs are not electrically isolated.The resolution of the A/D converter is 12 bits. Analog signals are conducted in shielded cables (seeThe analog inputs can be configured individually in a lot of different operating modes (even as digital inputs). The configuration is performed by setting certain bits in the system constants KW 86,00 to KW 86,07 as follows

Related Product Recommendation:

Product's Character:

The trigger of the self-protecting mechanism is displayed by the red LED Ovl as long as the overload is present. In the PLC system an error message is then stored (FK4, error number 4). The open-circuit monitoring begins below ca. 3 mA. The value of the range underflow is stored. If the ope circuit monitoring is configured, the open-circuit event is displayed by the red LED Ovl as long as it is present. In the PLC system an error message is stored (FK4, error number 9). The following figure shows the connection of 2-pole passive- type analog sensors 4...20 mA. If the analog current sensors 4...20 mA are powered from a separate power supply unit, the reference potentials 0V (of the separate power supply unit and the power supply unit for the 07 KT 94) must be interconnected
to each other.In the above example, the AGND terminal remains
unused.

CMA 121 3DDE 300 401 DC Power Supply Module ABB
CMA 122 CPU Card ABB
CMA 123 CMA123 Display Card ABB
CMA 124 Measuring Card ABB
CMA 125 Generator Card ABB
CMA 126 Interface Card ABB
CMA 132 Generator Relay Terminal Board ABB
CMA 133 3DDE 300 413 Terminal board ABB
CMA 136 Generator Relay Terminal Board ABB
CMA 137 Connection Module ABB
CMA131 Servo-motor Drive Encoder Module ABB
CMA135 Diesel Start Stop Automatic Module ABB
CMM11 Condition Monitoring Module ABB
CP501 1SBP260170R1001 Text Display ABB
CP502 1SBP 260171 R1001 Text Display Panel ABB
CP503 1SBP 260172 R1001 Text Display Panel ABB
CP511 1SBP 260173 R1001 Operator Panel - Graphics and Text ABB
CP512 1SBP 260174 R1001 Operator Panel - Graphics and Text ABB
CPU86-NDP 57287586 CPU Processor Board ABB
CS512 3BUR980009R1 CS512 DCN Interface Module ABB
CS513 3BSE000435R1 MasterBus 300E Communications Module ABB
CS513K01 3BSE004772R1 MasterBus 300E Communications Module ABB
CS513K02 3BSE004773R1 MasterBus 300E Communications Module ABB
CS513K04 3BSE055760R1 MasterBus 300/300E Comm. Interface for RJ45 ABB
CSC01 Loop Command Sequence Controller ABB
CT 370a GJR2 237500 R1, GJR2237500R0001 CT 370a Module ABB
CT 5536a HEIE420807R1, HEIE420807R0001 CT5536a Module ABB
CTT01 Configuration Tuning Terminal Bailey
CTT02 Handheld Configurator Tuning Terminal ABB
DAC85-10B 57574825BA ULMA D/A Converter Module ABB

DAI 01 P 37131-4-0369628 DAI01 Analog Input Module ABB
DAI 02 0369630M DAI 02 Analog Input Module ABB
DAI 03 P 37141-4-0369631 Analog Input Module ABB
DAI 04 P37131-4-0369632 Analog Input Module ABB
DAI 05 P 37131-4-0336025 DAI 05 Analog Input Module ABB
DAO 01 P 3717-4-0369629 DAO 01 Analog Output Module ABB

The use of the product: