Constant Force Briquette Testing Machine Calculated Automatically Material Curve

Product Specification

1. introduction

• This machine is applicable to metal, cementing compound, tubes, sectional bars, aerospace, petrochemical, waterproof rolls, wire and cable, textile, fiber, rubber, ceramics, food, mechanical packaging, geo-textile, film, wood, paper and other industries and quality supervision department, and it also can be used in college for teaching demonstration.
• Adopting precise auto control and data acquisition system to realize fully digital adjustment to data acquisition and control process. During tensile test, it can test max. bearing tensile, compression, tensile strength, deformation, elongation and other technical specifications;
• After tensile test, the above parameters can be calculated automatically through main controller according to the test parameters, which are set before test and meantime display the corresponding test results. All test parameters can be saved and inquired after test, also can be connected with printer to print test reports.

2. specification

(1) Ordinary test items: (normal display value and calculated value)
● tensile stress ● tensile strength
●Tear strength ● Elongation at break
●Fixed and tensile stress ●Constant elongation
●Constant stress value ●Tear strength
● Any point force value ● Any point elongation
●Extraction force ●Adhesion and peak value calculation
●Pressure test ●Adhesion peeling force test
●Bending test ● Pulling force puncture test
(2) Special test items:
Elastic Young's modulus
Definition: The ratio of the normal stress component to the normal strain in the same phase. To determine the coefficient of material stiffness, the higher the value, the stronger the material.
2. Example: The load can maintain a proportional relationship with the elongation within a certain range, and the maximum stress is the ratio limit.
3. Elastic limit: the maximum stress that the material can withstand without permanent deformation.
4. Elastic deformation: After the load is removed, the deformation of the material completely disappears.
5. Permanent deformation: After the load is removed, the material remains deformed.
6. Yield point: When the material is stretched, the deformation increases and the stress does not change. This point is the yield point. The yield point is divided into upper and lower yield points, and the above yield point is generally used as the yield point.
Yield: The load exceeds the proportional limit and is no longer proportional to the elongation. The load will suddenly drop, and then the ups and downs will rise and change over a period of time. This phenomenon is called yielding.
7. Yield strength: The quotient of the permanent elongation when the tensile strength reaches a certain value, divided by the original area of ​​the parallel portion.
8. Spring K value: the ratio of the force component to the deformation in the same phase as the deformation.
9. Effective elasticity and hysteresis loss:
On a tensile machine, when the sample is stretched to a certain elongation at a certain speed or stretched to a specified load, the percentage of the ratio of the work recovered during contraction and the work consumed during stretching is determined to be effective. Elasticity; the percentage of the ratio of the energy lost during elongation and contraction of the sample to the work consumed during elongation is the hysteresis loss.

The universal testing machine can also make bending and flexural test, shear test, peel test, high and low temperature test, assurance loading test, wedge test, etc. if equipped with relative test fixtures.

4. features

• This universal testing machine adopts two strong supports, precise load cell to measure the load. Its crosshead can move up or down at a constant speed.
• This universal testing machine can program the crosshead speed or conduct cyclical testing, allow testing at a constant force, testing at constant deformation, testing at constant displacement, etc.
• This testing machine can equip with extensometers to measure the extension or deformation.
• According to test requirement for temperature, humidity, pressure, etc, special device, such as environmental chamber can be placed around the test specimen to do test in certain temperature, humidity or pressure.
• Matched with various test fixture, like peal, puncture, tear, pneumatic grip, belt tension, etc. This UTM can be used to metal, non-metal, composite materials like rubber, steel wire, plastic, seat belt, textile character test.
• Protecting functions of over load, over current, over voltage, crosshead limit moving space protection, auto stop at break.

5. software introduction

• Easy to control and friendly interface

windows based interface, easy and fast to reach different functions, suitable for most of operators using habits. Integrated all common operation functions, like specimen information input, specimen choosing, curve plotting, data display, data process, data analysis, test operation etc., easy and convenient to operate.

• Full digital display and computer control

Adopting remote controller, fast response and reliable to parameter gathering. Realize digital adjustment and zeroing of load, deformation and displacement as well as PID parameter adjusting.

• Different control mode & speed setting
• Programmable control mode

Users can program test mode according to their own requirements.

• Load holding facility for a specific period:

Report is editable