AT91SAM7S256-AU-001 - ATMEL Corporation - AT91 ARM® Thumb®-based Microcontroller

Product Specification

Quick Detail:

AT91 ARM® Thumb®-based Microcontrollers

Description:

Atmel’s AT91SAM7S is a series of low pincount Flash microcontrollers based on the 32-bit ARM RISC processor. It features a high-speed Flash and an SRAM, a large set of peripherals, including a USB 2.0 device (except for the AT91SAM7S32), and a complete set of system functions minimizing the number of external components. The device is an ideal migration path for 8-bit microcontroller users looking for additional performance and extended memory.

The embedded Flash memory can be programmed in-system via the JTAG-ICE interface or via a parallel interface on a production programmer prior to mounting. Built-in lock bits and a security bit protect the firmware from accidental overwrite and preserves its confidentiality.

The AT91SAM7S Series system controller includes a reset controller capable of managing the

power-on sequence of the microcontroller and the complete system. Correct device operation

can be monitored by a built-in brownout detector and a watchdog running off an integrated RC

oscillator.

The AT91SAM7S Series are general-purpose microcontrollers. Their integrated USB Device

port makes them ideal devices for peripheral applications requiring connectivity to a PC or cellular phone. Their aggressive price point and high level of integration pushes their scope of use far into the cost-sensitive, high-volume consumer market.

Applications:

• Incorporates the ARM7TDMI® ARM® Thumb® Processor

– High-performance 32-bit RISC Architecture

– High-density 16-bit Instruction Set

– Leader in MIPS/Watt

– Embedded*ICE™ In-circuit Emulation, Debug Communication Channel Support

• Internal High-speed Flash

– 256 kbytes, organized in 1024 Pages of 256 Bytes (AT91SAM7S256)

– 128 kbytes, organized in 512 Pages of 256 Bytes (AT91SAM7S128)

– 64 kbytes, organized in 512 Pages of 128 Bytes (AT91SAM7S64)

– 32 kbytes, organized in 256 Pages of 128 Bytes (AT91SAM7S321/32)

– Single Cycle Access at Up to 30 MHz in Worst Case Conditions

– Prefetch Buffer Optimizing Thumb Instruction Execution at Maximum Speed

– Page Programming Time: 6 ms, Including Page Auto-erase, Full Erase Time: 15 ms

– 10,000 Write Cycles, 10-year Data Retention Capability, Sector Lock Capabilities,

Flash Security Bit

– Fast Flash Programming Interface for High Volume Production

• Internal High-speed SRAM, Single-cycle Access at Maximum Speed

– 64 kbytes (AT91SAM7S256)

– 32 kbytes (AT91SAM7S128)

– 16 kbytes (AT91SAM7S64)

– 8 kbytes (AT91SAM7S321/32)

• Memory Controller (MC)

– Embedded Flash Controller, Abort Status and Misalignment Detection

• Reset Controller (RSTC)

– Based on Power-on Reset and Low-power Factory-calibrated Brown-out Detector

– Provides External Reset Signal Shaping and Reset Source Status

• Clock Generator (CKGR)

– Low-power RC Oscillator, 3 to 20 MHz On-chip Oscillator and one PLL

• Power Management Controller (PMC)

– Software Power Optimization Capabilities, Including Slow Clock Mode (Down to

500 Hz) and Idle Mode

– Three Programmable External Clock Signals

• Advanced Interrupt Controller (AIC)

– Individually Maskable, Eight-level Priority, Vectored Interrupt Sources

– Two (AT91SAM7S256/128/64/321) or One (AT91SAM7S32) External Interrupt

Sources and One Fast Interrupt Source, Spurious Interrupt Protected

• Debug Unit (DBGU)

– 2-wire UART and Support for Debug Communication Channel interrupt,

Programmable ICE Access Prevention

• Periodic Interval Timer (PIT)

– 20-bit Programmable Counter plus 12-bit Interval Counter

• Windowed Watchdog (WDT)

– 12-bit key-protected Programmable Counter

– Provides Reset or Interrupt Signals to the System

– Counter May Be Stopped While the Processor is in Debug State or in Idle Mode

• Real-time Timer (RTT)

– 32-bit Free-running Counter with Alarm

– Runs Off the Internal RC Oscillator

• One Parallel Input/Output Controller (PIOA)

– Thirty-two (AT91SAM7S256/128/64/321) or twenty-one (AT91SAM7S32) Programmable I/O Lines Multiplexed with up to Two Peripheral I/Os

– Input Change Interrupt Capability on Each I/O Line

– Individually Programmable Open-drain, Pull-up resistor and Synchronous Output

• Eleven (AT91SAM7S256/128/64/321) or Nine (AT91SAM7S32) Peripheral DMA Controller (PDC) Channels

• One USB 2.0 Full Speed (12 Mbits per Second) Device Port (Except for the AT91SAM7S32).

– On-chip Transceiver, 328-byte Configurable Integrated FIFOs

• One Synchronous Serial Controller (SSC)

– Independent Clock and Frame Sync Signals for Each Receiver and Transmitter

– I²S Analog Interface Support, Time Division Multiplex Support

– High-speed Continuous Data Stream Capabilities with 32-bit Data Transfer

• Two (AT91SAM7S256/128/64/321) or One (AT91SAM7S32) Universal Synchronous/Asynchronous Receiver Transmitters (USART)

– Individual Baud Rate Generator, IrDA® Infrared Modulation/Demodulation

– Support for ISO7816 T0/T1 Smart Card, Hardware Handshaking, RS485 Support

– Manchester Encoder/Decoder (AT91SAM7S256/128)

– Full Modem Line Support on USART1 (AT91SAM7S256/128/64/321)

• One Master/Slave Serial Peripheral Interface (SPI)

– 8- to 16-bit Programmable Data Length, Four External Peripheral Chip Selects

• One Three (AT91SAM7S256/128/64/321)-channel or Two (AT91SAM7S32)-channel 16-bit Timer/Counter (TC)

– Three (AT91SAM7S256/128/64/321) or One (AT91SAM7S32) External Clock Inputs, Two Multi-purpose I/O Pins per

Channel

– Double PWM Generation, Capture/Waveform Mode, Up/Down Capability

• One Four-channel 16-bit PWM Controller (PWMC)

• One Two-wire Interface (TWI)

– Master Mode Support Only, All Two-wire Atmel EEPROMs Supported

• One 8-channel 10-bit Analog-to-Digital Converter, Four Channels Multiplexed with Digital I/Os

• SAM-BA™ Boot Assistant

– Default Boot program

– Interface with SAM-BA Graphic User Interface

• IEEE 1149.1 JTAG Boundary Scan on All Digital Pins

• 5V-tolerant I/Os, including Four High-current Drive I/O lines, Up to 16 mA Each

• Power Supplies

– Embedded 1.8V Regulator, Drawing up to 100 mA for the Core and External Components

– 3.3V or 1.8V VDDIO I/O Lines Power Supply, Independent 3.3V VDDFLASH Flash Power Supply

– 1.8V VDDCORE Core Power Supply with Brown-out Detector

• Fully Static Operation: Up to 55 MHz at 1.65V and 85°C Worst Case Conditions

• Available in a 64-lead LQFP Green Package (AT91SAM7S256/128/64/321) and 48-lead LQFP Green Package (AT91SAM7S32)

Specifications:

Competitive Advantage:

Warranty :180 days !
Free shipping: Order over $1000 win a free shipment fee
(goods weight below 3Kg) ,during 20130901-20130930 .

Why buy from us >>> Fast / Safely / Conveniently

•    Mega Source is a Stock keeper and trade company of Electronic components .Our branches office include China, Hong Kong, Sigapore , Canada . Offer business, service, resourcing and information for our global member.
•    Goods are ensured the highest quality possible and are delivered to our customers all over the world with speed and precision.
 

How to buy >>>

•    Contact us by email & sent your inquire with your Transport destination .
•    Online chat, the commissioner would be responded ASAP.
 

Service >>>

•    Forwarder Shipment to world-wide, DHL ,TNT ,UPS,FEDEX etc.  buyer don`t need to worry about shipping problem
•    We will try to respond as quickly as possible. But due to time zone difference, please allow up to 24 hours to get your mail replied. The products were tested by some devices or software, we ensure that there is no quality problems.
•    We are committed to providing fast, convenient and safe transportation service to global buyer.