Shenzhen OptoElectronics Co., Ltd.
| Payment Terms | T/T |
| Supply Ability | 10000pcs per months |
| Delivery Time | 3working days |
| Packaging Details | Carton box |
| Data port | RJ-45 |
| Package | SFP Small Form Factor |
| Power Supply | 3.3V |
| Distance | 30meter for 10G (CAT6A cable) |
| Case temperature | 0°C to +70°C or -40°C to +85°C |
| Data rate | • Support 10Gbase-T / 5Gbase-T / 2.5Gbase-T / 1000base-T on line port |
| Brand Name | OptoElectronics |
| Model Number | SFP-10G-T |
| Certification | CE |
| Place of Origin | China |
View Detail Information
Explore similar products
1000BASE-LX 1310NM 10KM SFP DDM Transceiver For Optical Links
1310NM 20KM DDM SFP Transceiver Operating Data Rate Up To 1.25Gbps
10G SFP Transceiver 10Gb/S Short Wavelength Pluggable SR
20km DOM Duplex LC SMF Transceiver Module Compatible 1000BASE-CWDM SFP
Product Specification
| Payment Terms | T/T | Supply Ability | 10000pcs per months |
| Delivery Time | 3working days | Packaging Details | Carton box |
| Data port | RJ-45 | Package | SFP Small Form Factor |
| Power Supply | 3.3V | Distance | 30meter for 10G (CAT6A cable) |
| Case temperature | 0°C to +70°C or -40°C to +85°C | Data rate | • Support 10Gbase-T / 5Gbase-T / 2.5Gbase-T / 1000base-T on line port |
| Brand Name | OptoElectronics | Model Number | SFP-10G-T |
| Certification | CE | Place of Origin | China |
Features
¨ Support 10Gbase-T / 5Gbase-T / 2.5Gbase-T / 1000base-T on line port
¨ Support 10Gbase-R on the host port
¨ Hot-pluggable SFP footprint
¨ Compact RJ-45 connector assembly
¨ RoHS-compliant and lead-free
¨ Single +3.3V power supply
¨ 10 Gigabit Ethernet over Cat 6a cable
¨ Ambient Operating temperature: 0°C to +70°C or -40°C to +85°C
Description
SFP-10G-T Copper Small Form Pluggable (SFP) transceivers are based on the SFP Multi Source Agreement (MSA) . They are compatible with the 10Gbase-T / 5Gbase-T / 2.5Gbase-T / 1000base-T standards as specified in IEEE Std 802.3 . SFP-10G-T uses the SFP's RX_LOS(must be pulled up on host) pin for link indication. If pull up or open SFP's TX_DISABLE pin, PHY IC be reset.
Cable Length
| Line Port | Cable | Reach | Host Port |
| 10Gbase-T | CAT6A | 30m | 10GBase-R |
| 5Gbase-T | CAT5E | 50m | 10GBase-R |
| 2.5Gbase-T | CAT5E | 50m | 10GBase-R |
| 1000base-T | CAT5E | 100m | 10GBase-R |
Pin Descriptions
| Pin | Symbol | Name/Description | Ref. |
| 1 | VEET | Transmitter Ground (Common with Receiver Ground) | 1 |
| 2 | TFAULT | Transmitter Fault. Not supported. | |
| 3 | TDIS | Transmitter Disable. Laser output disabled on high or open. | 2 |
| 4 | MOD_DEF(2) | Module Definition 2. Data line for Serial ID. | 3 |
| 5 | MOD_DEF(1) | Module Definition 1. Clock line for Serial ID. | 3 |
| 6 | MOD_DEF(0) | Module Definition 0. Grounded within the module. | 3 |
| 7 | Rate Select | No connection required | |
| 8 | LOS | High indicates no linked. low indicates linked. | |
| 9 | VEER | Receiver Ground (Common with Transmitter Ground) | 1 |
| 10 | VEER | Receiver Ground (Common with Transmitter Ground) | 1 |
| 11 | VEER | Receiver Ground (Common with Transmitter Ground) | 1 |
| 12 | RD- | Receiver Inverted DATA out. AC Coupled | |
| 13 | RD+ | Receiver Non-inverted DATA out. AC Coupled | |
| 14 | VEER | Receiver Ground (Common with Transmitter Ground) | 1 |
| 15 | VCCR | Receiver Power Supply | |
| 16 | VCCT | Transmitter Power Supply | |
| 17 | VEET | Transmitter Ground (Common with Receiver Ground) | 1 |
| 18 | TD+ | Transmitter Non-Inverted DATA in. AC Coupled. | |
| 19 | TD- | Transmitter Inverted DATA in. AC Coupled. | |
| 20 | VEET | Transmitter Ground (Common with Receiver Ground) | 1 |
Notes:
1. Circuit ground is connected to chassis ground
2. PHY disabled on TDIS > 2.0V or open, enabled on TDIS < 0.8V
3. Should be pulled up with 4.7k - 10k Ohms on host board to a voltage between 2.0 V and 3.6 V. MOD_DEF(0) pulls line low to indicate module is plugged in.
+3.3V Volt Electrical Power Interface
The SFP-10G-T has an input voltage range of 3.3 V +/- 5%. The 4V maximum voltage is not allowed for continuous operation.
| +3.3 Volt Electrical Power Interface | ||||||
| Parameter | Symbol | Min | Typ | Max | unit | Notes/Conditions |
| Supply Current | Is | 900 | 1200 | mA |
4W max power over full range of voltage and temperature. See caution note below |
|
| Input Voltage | Vcc | 3.13 | 3.3 | 3.47 | V | Referenced to GND |
| Maximum Voltage | Vmax | 4 | V | |||
| Surge Current | Isurge | TBD | mA |
Hot plug above steady state current. See caution note below |
||
Caution: Power consumption and surge current are higher than the specified values in the SFP MSA
Low-Speed Signals
MOD_DEF(1) (SCL) and MOD_DEF(2) (SDA), are open drain CMOS signals (see section VII, "Serial Communication Protocol"). Both MOD_DEF(1) and MOD_DEF(2) must be pulled up to host_Vcc.
| Low-Speed Signals, Electronic Characteristics | |||||
| Parameter | Symbol | Min | Max | unit | Notes/Conditions |
| SFP Output LOW | VOL | 0 | 0.5 |
V
|
4.7k to 10k pull-up to host_Vcc, measured at host side of connector |
| SFP Output HIGH | VOH | host_Vcc -0.5 | host_Vcc + 0.3 |
V
|
4.7k to 10k pull-up to host_Vcc, measured at host side of connector |
| SFP Input LOW | VIL | 0 | 0.8 | V |
4.7k to 10k pull-up to Vcc, measured at SFP side of connector
|
| SFP Input HIGH | VIH | 2 | Vcc + 0.3 | V |
4.7k to 10k pull-up to Vcc, measured at SFP side of connector |
High-Speed Electrical Interface
All high-speed signals are AC-coupled internally.
| High-Speed Electrical Interface, Transmission Line-SFP | ||||||
| Parameter | Symbol | Min | Typ | Max | unit | Notes/Conditions |
| Line Frequency | fL | 125 | MHz |
5-level encoding, per IEEE 802.3 |
||
| Tx Output Impedance | Zout,TX | 100 | Ohm |
Differential, for all frequencies between 1MHz and 125MHz |
||
| Rx Input Impedance | Zin,RX | 100 | Ohm |
Differential, for all frequencies between 1MHz and 125MHz |
||
| High-Speed Electrical Interface, Host-SFP | ||||||
| Parameter | Symbol | Min | Typ | Max | unit | Notes/Conditions |
|
Single ended data input swing |
Vinsing | 250 | 1200 |
mV
|
Single ended | |
|
Single ended data output swing |
Voutsing | 350 | 800 | mV | Single ended | |
| Rise/Fall Time | Tr,Tf | 175 | psec | 20%-80% | ||
| Tx Input Impedance | Zin | 50 | Ohm | Single ended | ||
| Rx Output Impedance | Zout | 50 | Ohm | Single ended | ||
General Specifications
| General | ||||||
| Parameter | Symbol | Min | Typ | Max | unit | Notes/Conditions |
| Data Rate | BR | 1 | 10.3125 | Gb/sec |
IEEE 802.3 compatible. See Notes 1,2 below |
|
Notes:
1. Clock tolerance is +/- 50 ppm
Environmental Specifications
Automatic crossover detection is enabled. External crossover cable is not required
| Environmental Specifications | ||||||
| Parameter | Symbol | Min | Typ | Max | unit | Notes/Conditions |
| Operating Case Temperature | Commercial | Tc | 0 | +70 | °C | |
| Industry | -40 | +85 | °C | |||
| Storage Temperature | -40 | +85 | °C | |||
Ordering information
| Part number | Speed mode | Temp |
| SFP-10G-TA1-C | 10G/5G/2.5G/1.25G | 0~70℃ |
| SFP-10G-TA1-I | 10G/5G/2.5G/1.25G | -40~85℃ |
Company Details
Business Type:
Manufacturer,Distributor/Wholesaler,Exporter
Total Annual:
>1000000
Employee Number:
>100
Ecer Certification：
Site Member
We are increasing thescale of trade and customers through out the world. With our good reputation we have won the trust of our customers. It’s helps the modernisation of our country and promote the economic and technical exchanges with the rest of the world. We also look forward to enhance the... We are increasing thescale of trade and customers through out the world. With our good reputation we have won the trust of our customers. It’s helps the modernisation of our country and promote the economic and technical exchanges with the rest of the world. We also look forward to enhance the...
Get in touch with us
Leave a Message, we will call you back quickly!